Lab tests results

homemade testosterone recipe

how  to cook  250mg/Ml Recipe For Test Cypionate (250mg/Ml )

Product Specifications/Features
    • 250mg/Ml Recipe for 20ml Test Cypionate
    • Many customers always say they were cheated by the supplier of injectable steroids, because the injection always not effect like the supplier say.
    • So I am really glad to help these customers (like you) get the best injection, it is really convenience to you.
    • First, I can provide you great half finished oil, you just need to filter it and then you will get the best injection.
    • Second, I also can provide you high quality raw powders. Then I will help you convert powder into injection step by step with the picture.
    • It is easy for you, sure you can get it.
    • For example:
    • Test Cypionate conversion 20ml @ 250mg/ml
    • 5 grams test cyp
    • 1ml Benzyl Alcohol
    • 15.25 ml sesame oil
    • Step1:
    • Weigh out 5 grams of powders.
    • Step 2:
    • Add Solvents and oil to the Beaker
    • Step 3:
    • Add the steroid powder to the Beaker containing oil and solvents
    • Step 4:
    • Stir steroid powder into solution
      • Step 13:
      • Push the solution through the whatman syringe filter into the sterile vial, then you will get the injection

      prepare

       

      We take Testosterone Cypionate powder 100 mg/mL for example.

      Each mL of the 100 mg/mL solution contains:

      Testosterone Cypionate powder……………………………………………………………………. 100 mg

      Benzyl benzoate ……………………………………………………………………………… 0.1 mL

      Cottonseed oil ………………………………………………………………………………… 736 mg

      Benzyl alcohol (as preservative)………………………………………………………… 9.45 mg

      Syringe (Any size)

      Sterile Glass Vial (Any size)

      Needles

      Thermometer

      Sterile Syringe filter 22um

      Digital scales measuring to 0.01g

       


      First–Weigh the Testosterone Cypionate into the glass beaker as shown above, add the Benzyl Alcohol and Benzyl Benzoate.

       

      steroids

       

      Second –The solvents will begin immediately dissolving the powder but in order to speed the process up it is possible to use a water bath.

       

       

      #anabolic #steroids #raw #powder #bodybuilding #fitness #fat loss #sex hormones #SARMS #PCTdrugs #HGH #homebrew #ugl # 33

       

      Pace the vial into a few cm of water in a pan or something similar: it is important not to use water that is too hot because this will cause some products to oxidize-150f is a good temperature to use, alternatively boiled water from the kettle. The carrier oil should be the same temperature as the solution when it is added so if you warm the solution in a water bath you should also the same to the carrier oil.

       

      The objective at this point is simply to fully dissolved the powder into the solvents. There should be no “Hormone swirls” or any visible powder remaining in the solution and once this is achieved move on to the next step.

       


       

      Then–Add the warmed Cottonseed oil to the solution

       

      #anabolic #steroids #raw #powder #bodybuilding #fitness #fat loss #sex hormones #SARMS #PCTdrugs #HGH #homebrew #ugl #

       

      this case 736ml must be added. Mix thoroughly again, there should be no hormone swirls-once this occurs remove immediately from the water bath and move on to the filtering process.

      Above: The steroid powder is fully dissolved in the solvents, the carrier oil is added and the product is ready to be filtered.

       


       

      Next–Draw up the solutions into the syringe you will be filtering with

       

      #anabolic #steroids #raw #powder #bodybuilding #fitness #fat loss #sex hormones #SARMS #PCTdrugs #HGH #homebrew #ugl # 55

       

      this can be a single large syringe or this can be repeated multiple times with a smaller syringe. Remove the 0.22um sterile syringe filter from it’s packing and fix the green needle to the smaller side and then apply to the syringe.

      Wipe the top of the sterile vial with an Alcohol swab and insert the green needle in it, put the needle attached to the syringe filter into the vial as shown below:

      Notes: The second needle equalizes the pressure as the solution enters the vial. Apply pressure to the syringe plunger to the filter the mixture. This is the most important part of this entire process as it is what sterilizes your product. All finished steroids from any steroid lab must go through this very process.

       

      Occasionally one may find that the filter gets blocked or that the process slows drastically-it is acceptable to replace the filter with a new one if this occurs to save time. The time it takes to filter steroids depends on whichsteroid powder is being filtered and how much is being filtere, as well as the mg/ml of the product.

       


       

      Finally–-Once the product is filtered in the sterile vial the process is complete.Then you can start to use.

       

      Related posts

      Leave a Comment